Omron PLC Training Course

With CX-Programmer that included in CX-One Package you can Program Below PLC Series
CP1E, CP2E, CP1L, CP1H, CJ2M, CS1
You can the CX-Programmer Trial Version from Omron Website.
Also after seeing the video you can send any question to me I can answer your questions.
Also, this course can be edited at your request.
Course Details
- DIFU/DIFD
* DIFU(013) turns the designated bit ON for one cycle when the execution condition goes from OFF to ON (rising edge).
* DIFD(014) turns the designated bit ON for one cycle when the execution condition goes from ON to OFF (falling edge).
- TIMX
* TIM or TIMX(550) operates a decrementing r with units of 0.1-s.
- CNT/CNTX
* CNT/CNTX(546) operates a decrementing counter.
- KEEP/SET/RSET
* KEEP Operates like a latching relay.
* SET turns the operand bit ON when the execution condition is ON. After this, the specified contact will remain ON regardless of ON/OFF of the input condition.
* RSET turns the operand bit OFF when the execution condition is ON. After this, the specified contact will remain OFF regardless of ON/OFF of the input condition.
- MOV
*Transfers a word of data to the specified word.
- CMP
* Input comparison instructions compare two values (constants and/or the contents of specified words) and create an ON execution condition when the comparison condition is true. Input comparison instructions are available to compare signed or unsigned data of one-word or double-length data.
- CMP/CMPL
* CMP : Compares two unsigned binary values (constants and/or the contents of specified words) and outputs the result to the Arithmetic Flags in the Auxiliary Area.
* CMPL : Compares two double unsigned binary values (constants and/or the contents of specified words) and outputs the result to the Arithmetic Flags in the Auxiliary Area.
- INC/DEC
* Increments the 4-digit hexadecimal content of the specified word by 1.
* Decrements the 4-digit hexadecimal content of the specified word by 1.
- ASL/ASR
* ASL : Shifts the contents of Wd one bit to the left.
* ASR : Shifts the contents of Wd one bit to the right.
- SLD/SRD
* SLD : Shifts data by one digit (4 bits) to the left.
* SRD : Shifts data by one digit (4 bits) to the right.
- BSET
* Copies the same word to a range of consecutive words.
- MOVB
* Transfers the specified bit.
- MOVD
* Transfers the specified digit or digits. (Each digit is made up of 4 bits.)
- NASL/NASR
* NASL : Shifts the specified 16 bits of word data to the left by the specified number of bits.
* NASR : Shifts the specified 16 bits of word data to the right by the specified number of bits.
- MCMP
* Compares 16 consecutive words with another 16 consecutive words and turns ON the correspond­ing bit in the result word where the contents of the words are not equal.
- MTIM
* Compares 16 consecutive words with another 16 consecutive words and turns ON the correspond­ing bit in the result word where the contents of the words are not equal.
- TCMP
*Compares the source data to the contents of 16 consecutive words and turns ON the corresponding bit in the result word when the contents of the words are equal.
- TIML
* TIML(542)/TIMLX(553) operates a decrementing r with units of 0.1s.
- TTIM
* TTIM(087)/TTIMX(555) operates an incrementing r with units of 0.1-s.
- SETA/RSTA
* SETA(530) turns ON the specified number of consecutive bits.
* RSTA(531) turns OFF the specified number of consecutive bits.
- OUTB
* OUTB(534) outputs the status of the instruction's execution condition to the specified bit.
- XFER
* Transfers the specified number of consecutive words.
- XCHG
* Exchanges the contents of the two specified Words

Bner and advanced user



Omron PLC Training Course Fast Download
Omron PLC Training Course Full Download